Hi all

We had a power cut at the weekend and I've only just realised that Moodle isn't accessible.

It is a Turnkey Appliance (64 bit 2.6.x Linux) running on VMWare. I can ping the Moodle server IP Address and also connect without a problem to Webmin but when I try to get to the actual Moodle Server to login, it just says the webpage cannot be displayed.

Any ideas? It was working fine before the power cut. I can't see any problems when looking at the appliance in VMWare vSphere.

Hello,

I've accidentally emptied config file and would like to get content of original one...

I'm on

Welcome to Redmine, TurnKey Linux 12.0 / Debian 6.0.7 Squeeze

Any way to recreate this config file ?

Thanks in advance,

regards,

Bulek.

I need to increase the size of the volume on a Turnkey EC2 microinstance of vTiger (production instance).

Can I confirm the procedure here:

1. Stop the instance.

2. Take a snapshot of the volume.

3. Recreate a new volume from the snapshot of increased size.

4. Detach old volume and reattach new volume (heeding mount points.

5. Restart the instance.

Hi

I'm try to setup an email server on a CentOS system with Postfix, Dovecot and MySQL.

I'm following this article for an Ubuntu system:
    https://library.linode.com/email/postfix/postfix2.9.6-dovecot2.0.19-mysql

Hello,

granted that I'm writing about a ubuntu-10.04-turnkey-lamp_11.3-1_i386 template, virtualized and contained in a CT of a Proxmox Host, I'm facing in a strange issue after a monthly-scheduled upgrade of this distro happened two months ago (December 2013).

First of all, I've to say that I've token notice of this issue, which I'm about to expose, just after a power-failure happened 3 weeks ago. Then, networking service wasn't able to get start up at the system boot, whereas it was able to do it manually.

I have been running proxmox ve with KVM for a while now.  Decided recently to give TKL a go within proxmox, and it has been a bad experience so far.

The containers install OK (but show errors where one would expect the initialization scripts would have been run) .. after proxmox CT install, system boots into a console CLI prompt, where I am able to login.

All attempts (via proxmox 'vzctl enter'  OR via the web console OR via an ssh session direct on the appliance) to initialize the container fails with similar error messages as below ..

Hi 

Trying to get the following command setup so it will boot once on next reboot, 

           /usr/lib/inithooks/firstboot.d/15regen-sslcert

The command recreates the SSL certificate.

Couple of questions 

1. where do I put the command/have to do so it will run only once?

2. Is there anything else that needs to be done to the machine to prevent confusion with other machines on the network (dhcp is enabled)?

Thanks

nicksoph

From the GitHub documentation I am hung pretty early.  Using I386 for architecture:

ARCH=$(dpkg --print-architecture)
CODENAME=$(lsb_release -s -c)
SOURCEFORGE="http://downloads.sourceforge.net/project/turnkeylinux"

cd /turnkey/fab/bootstraps
wget $SOURCEFORGE/bootstrap/bootstrap-$CODENAME-$ARCH.tar.gz

If I follow the instructions, I assume I need to be in "/" root entering the first ARCH, CODENAME and SOURCEFORGE variable declarations.

This time I get awaiting response... 302 found

connected......  bootstrap-wheezy-i386.tar.gz

Hi,

We are evaluating a TKLinux appliance on AWS on the Free Tier (12 month) and wanted to check that backups could be restored properly to a new instance (rather than risk corrupting the exisitng appliance we are currently running)

To do this we had to upgrade to the $10/month pay-per-use tariff (you can only have one instance on the free tier) and it looked as if we could upgrade/downgrade as required.

Hello,

I've setup and deployed the Revision-Control using build "VM" within our domain environment.

How can I get uses to authenticate against active directory using LDAP?

Is there a package I need to install using Webmin?

Has anyone installed openldap on this build?

Thanks!